Beta65 1S Brushless BNF Whoop Quadcopter (F4 version) Frsky

  • Sale
  • Regular price $159.99 AUD
  • IN STOCK!


Note: the new Beta65 Pro is currently only available in FrSky protocol. Flysky and DSMX coming soon.

There is a whole lot of crap out there when it comes to brushless micros in the whoop form factor.

We've been really particular about our decision making process in stocking brushless whoops.

The market has recently been inundated by cheap and nasty (but in reality - quite pricey), well, crap.

Traditionally brushless whoops - particularly the 'affordable' ones, had sported brushless motors that have been unreliable and underpowered, sitting on flimsy, fragile frames and driven by flight controllers just too inaccurate to enjoy that locked in feeling you need to hit those tight gaps that make whooping fun!

That is, until now!

We are happy to offer our customers the new and improved upgraded Beta65 pro brushless whoop.

Sporting 19,000kv (Yes! 19,000kv) brushless motors, with innovative new e-clip design to prevent bell fly-offs, mounted on the BEST and most durable brushless whoop frame available - the new and improved BetaFPV 65 pro frame and driven by the brand new BetaFPV F4 flight controller with integrated FrSky SPI long range receiver with OSD, telemetry AND an open UART for Smart Audio. The rock solid BetaFPV Z01 mullet AIO camera provides rock solid, low latency FPV. 

All this packed in to the traditional 65mm tiny whoop ducted form factor.

 

SPARES COMPATIBILITY

Props 31mm - 1mm shaft diameter (shaft diameter is important - brushed props have a 0.8mm diameter and will need to be drilled out to 1mm to be compatible (coming very soon)

Frame BetaFPV Beta 65 Pro frame

Motors 0603

Battery Any tiny whoop "stick" style 1S battery with powerwhoop connector (260-300mah recommended)

Canopy All canopies we stock

 

THE IMPORTANT STUFF

  • Frame: 65pro frame
  • Propeller: 31mm 4-blades propellers (1mm shaft hole)
  • Motors: 0603 19,000KV
  • Fligh Controller: BETAFPV F4 1S brushless FC
  • Firmware version: betaflight_matekf411rx_3.4.0
  • ESC: 5A/6A preak BLHeli DSHOT600 ESC (integrated with FC)
  • Camera & VTX: Z01 25mW AIO mullet VTX camera
  • Battery: 260mAh Lipo HV Battery
  • Receiver: Built-in Frsky SPI RX 
  • Weight: 23.29g (without battery)
  • Flight time: 2.5 minutes with 260mAh HV battery

 

THE COMPONENTS

The flight controller

Comparing the old F3 Brushless FC & the new F4 Brushless FC

   

 

  • CPU: STM32F411CEU6 (100MHZ )
  • Six-Axis: MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
  • Size: 26mm x 26mm, fully compatible with the Inductrix quad frame, Beta65 Pro frame, Beta75 Pro frame, BWhoop B06 frame and mounting pattern
  • Firmware version: betaflight_matekf411rx_3.4.0
  • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
  • Built in SPI Frsky D8 protocol native receiver
  • Power supply: 1S
  • ESC Current: 5A continuous and peak 6A (3 seconds)
  • ESC BLHeliSuite programmable
  • ESC Factory firmware: O_L_5_REV16_6.HEX
  • ESC Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM
  • Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
  • Weight: 4g 

What is SPI?

Basically, SPI is a communication protocol like UART, a serial communication protocol. A SPI connection requires 4 wires, while an UART connection only uses 2 (TX and RX). However SPI is faster than UART and places less stress on the processor.

Currently the built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules with International Firmware (in D8 mode). Pay attention, this is a SPI connection receiver. In Betaflight Configuration, it should be setted as FRSKY_D receiver in SPI RX mode.

 

The motors

The frame

The Beta65 Pro BNF sports the new and improved Beta65 Pro frame.

 

WHAT'S INCLUDED

  • 1 x Beta65 Pro 1S FrSky Brushless BNF micro whoop quadcopter drone
  • 1 x BetaFPV 260mah HV battery

Customer Reviews

Based on 1 review Write a review